COMTROL CORPORATION ROCKETPORT 485 Card Type Serial card Chip Set Unidentified I/O options 8 Serial ports via 25-pin connector Data Bus 16-bit ISA [Image] CONNECTIONS Function Label Function Label 8 serial ports vis CN1 DC power connector CN2 25-pin connector Note: Connector is used to supply voltage to peripheral devices through ports 3-8. Power may be supplied through 25-pin or 9-pin serial connectors. PORT 1 MODE SELECTION Mode JP1/A JP1/B JP1/C JP1/D JP1/E JP1/F RS-232 Pins 2 Pins 2 Pins 2 Pins 2 Pins 2 Pins 2 & 3 & 3 & 3 & 3 & 3 & 3 RS-485 Pins 1 Pins 1 Pins 1 Pins 1 Pins 1 Pins 1 & 2 & 2 & 2 & 2 & 2 & 2 Note: Pins designated are in the closed position. RJ-485 ports must also be software configured. PORT 2 MODE SELECTION Mode JP2/A JP2/B JP2/C JP2/D JP2/E JP2/F RS-232 Pins 2 Pins 2 Pins 2 Pins 2 Pins 2 Pins 2 & 3 & 3 & 3 & 3 & 3 & 3 RS-485 Pins 1 Pins 1 Pins 1 Pins 1 Pins 1 Pins 1 & 2 & 2 & 2 & 2 & 2 & 2 Note: Pins designated are in the closed position. RJ-485 ports must also be software configured. PORT 3 POWER Setting JP3 » Disabled Open +5V Closed Note: Port is equipped with a fuse to break the circuit if the device draws more than .5 amp. PORT 4 POWER Setting JP4 » Disabled Open +5V Closed Note: Port is equipped with a fuse to break the circuit if the device draws more than .5 amp. PORT 5 POWER Setting JP5 » Disabled Open +5V Closed Note: Port is equipped with a fuse to break the circuit if the device draws more than .5 amp. PORT 6 POWER Setting JP6 » Disabled Open +5V Closed Note: Port is equipped with a fuse to break the circuit if the device draws more than .5 amp. PORT 7 POWER Setting JP7 » Disabled Open +5V Closed Note: Port is equipped with a fuse to break the circuit if the device draws more than .5 amp. PORT 8 POWER Setting JP8 » Disabled Open +5V Closed Note: Port is equipped with a fuse to break the circuit if the device draws more than .5 amp. BOARD 1 ADDRESS SELECTION Setting SW1/1 SW1/2 SW1/3 SW1/4 SW1/5 SW1/6 SW1/7 SW1/8 100h Off On Off On On On On On 140h On Off Off On On On On On » 180h Off Off Off On On On On On 200h Off On On Off On On On On 240h On Off On Off On On On On 280h Off Off On Off On On On On 300h Off On Off Off On On On On 340h On Off Off Off On On On On 380h Off Off Off Off On On On On Note: Board one switch settings determines other controller settings. A different address should be selected for each board. BOARD 2 ADDRESS SELECTION Setting SW1/1 SW1/2 SW1/3 SW1/4 SW1/5 SW1/6 SW1/7 SW1/8 100h Off On Off On On On On On 140h On Off Off On On On On On 180h Off Off Off On On On On On 200h Off On On Off On On On On 240h On Off On Off On On On On 280h Off Off On Off On On On On 300h Off On Off Off On On On On 340h On Off Off Off On On On On 380h Off Off Off Off On On On On BOARD 3 ADDRESS SELECTION Setting SW1/1 SW1/2 SW1/3 SW1/4 SW1/5 SW1/6 SW1/7 SW1/8 100h Off On Off On On On On On 140h On Off Off On On On On On 180h Off Off Off On On On On On 200h Off On On Off On On On On 240h On Off On Off On On On On 280h Off Off On Off On On On On 300h Off On Off Off On On On On 340h On Off Off Off On On On On 380h Off Off Off Off On On On On BOARD 4 ADDRESS SELECTION Setting SW1/1 SW1/2 SW1/3 SW1/4 SW1/5 SW1/6 SW1/7 SW1/8 100h Off On Off On On On On On 140h On Off Off On On On On On 180h Off Off Off On On On On On 200h Off On On Off On On On On 240h On Off On Off On On On On 280h Off Off On Off On On On On 300h Off On Off Off On On On On 340h On Off Off Off On On On On 380h Off Off Off Off On On On On